Tile Adhesive

Plasticising and hydrogen free expansion grout admixture Uses Cebex EN is an admixture for cement grouts where a reduced water / cement ratio and positive expansion are required. Applications include bed grouting, duct grouting, non-shrink infi lling and jointing. Cebex EN Meets the EN447 - 2007 Requirements of Grouts for Prestressing tendons. Advantages  Hydrogen free expansion system compensates for plastic shrinkage and settlement in properly designed cementitious grout.  Reduced water / cement ratio in the grout mix ensures low permeability and long term durability in service.  Gives high grout fl uidity with low water / cement ratio, thus making placement or injection of the grout easy.  No metallic iron content to corrode and cause staining or deterioration due to rust expansion in the grout.  Composition allows high early strength development in grouts, without the use of chlorides. Description Cebex EN a plasticising and hydrogen free expansion grout admixture is supplied as a powder admixture. Cebex EN allows the use of a reduced water / cement ratio with consequent increased strengths and durability. The expansive medium counteracts the natural settlement and plastic shrinkage of the grout and aids stability and cohesion

High strength underwater fl exible epoxy concrete and mortar Uses For the fast and permanent reinstatement of concrete, particularly where high strength, abrasion, impact and chemical resistance are required. The product is designed for underwater applications. It is ideally suited for reinstatement of defective concrete surface in bridges, dams, foundations, slabs, joints in highways, concrete runways and for use as a bedding material. Advantages  Most suited for underwater applications  Solvent free  Dimensionally stable hardening  High compressive and abrasion strengths  Curing unaffected by humidity  Suitable for both damp and dry surfaces  Rapid hardening at low temperatures  Impact resistant Description Expocrete EUW is a solvent free, epoxy based underwater repair concrete, which is supplied as three component system. Technical support The company provides a technical advisory service supported by a team of specialists in the fi eld.

PRODUCT DATA SHEET SikaGrout®-214 IN High strength non-shrink pourable cementitious precision grout DESCRIPTION SikaGrout®-214 IN is a cement based 1-component, ready to mix, non-shrink, pourable and flowable, two stage expanding engineering grout in dry powder form. It is widely used for precision grouting in engineering applications subjected to static and dynamic loads. USES To grout bearings, machine foundations, columns joints in precast construction etc. ▪ ▪ To grout anchors in concrete ▪ To grout cavities, gaps and voids in concrete To grout base plate of turbine, compressor, boilers, pumps and heavy machinery ▪ ▪ Sealing around penetrations ▪ Post fixings CHARACTERISTICS / ADVANTAGES ▪ Dual shrinkage compensated ▪ Suitable for temperature of above 0 °C up to +200 °C ▪ Easy to mix, only add water ▪ Adjustable consistency ▪ Very good flow characteristics ▪ Rapid strength development ▪ Excellent bond to concrete ▪ No segregation or bleeding ▪ High final strengths ▪ Initial expansion by gas generation ▪ Impact and vibration resistant Non-corrosive to anchor bolts, base plate / saddle / frame, sliding plate ▪ ▪ Not harmful to concrete and reinforcing steel ▪ Not flammable ▪ Non-toxic ▪ Frost, oil and fire resistant ▪ Require normal curing Suitable to use under restraints and grout thickness required ▪ ▪ Expansive to counteract initial shrinkage Maximum flow distance is compatible to the dimensions of base plate / saddle / frame ▪ Resistant to the chemicals, gases etc. being handled in equipment ▪ ▪ Chloride free PRODUCT INFORMATION Product declaration ASTM C1107 Chemical base Portland cement, special additives and aggregates Packaging 30 kg bag Shelf life 6 months from date of production Storage conditions The product must be stored properly in undamaged and unopened original sealed packaging in dry conditions at temperatures between +5 °C and +35 °C. Protect from moisture, direct sunlight and frost.

High performance low viscosity PCE based  admixture for early strength.UsesAuracast 270M is a high performance super plasticizer suitable  for precast concrete industry to obtain high early strength and  moderate workability retentions are required.Auracast 270M developed to use in:Moderate workability retention concrete.Also Suitable for cement replacement concrete such as  fl y ash, GGBFS and micro silica.High performance concrete.High early strength.AdvantagesLow viscosity admixture suitable for precast industrySuitable for concrete having cement replacements and low water cement ratioProvides high early strength without increase in cement  content or reduction in workability. Ideal for precast concrete  productionReduce rate of workability loss normally associated with  super plasticiser. Reduces shrinkage cracking because  of lower water cement ratio. Makes the concrete water  impermeableBetter resistance to CarbonationReduce Shrinkage and CreepIncreased durability

PRODUCT DATA SHEET SikaCeram®-288 Flex S1 Cementitious high performance deformable adhesive with no vertical slip and extended open time for thin tiles, large tiles and demanding applications (Formerly SikaCeram®-288 H) DESCRIPTION SikaCeram®-288 Flex S1 is a cementitious, deformable, high performance floor and wall tile adhesive with reduced slip and extended open time. For residential, industrial and commercial wet and dry environments up to 15 mm thickness. Suitable for bonding all types of ceramic, porcelain, marble and natural stone tiles to all types of absorbent construction material substrates. Particularly suitable for façades, heated floors, swimming pools and industrial floors. Indoor and outdoor use. EN 12004: Classification C2TES1*. USES Bonding the following types of tiles: ▪ Ceramic ▪ Vitrified ▪ Earthenware ▪ Glazed ▪ Porcelain ▪ Stoneware ▪ Terrazzo ▪ Unglazed ▪ Thin and large tiles ▪ Marble and natural stone Bonding tiles for the following applications: ▪ Wall and floor ▪ Balconies ▪ Bathrooms ▪ Commercial / Residential environments ▪ Heated floors (water and electric systems) ▪ Kitchens ▪ Leisure centres ▪ Storage areas ▪ Terraces ▪ Wet areas ▪ Overlaying existing interior ceramic tiles High demanding areas such as swimming pools, industrial and heavy trafficked floors, façades ▪ ▪ Interior and exterior use CHARACTERISTICS / ADVANTAGES ▪ Layer thickness: 1–15 mm ▪ Deformable ▪ Extended open time ▪ Reduced vertical slip ▪ Smooth application Typical bonding substrates: Cementitious screed, concrete, plaster, ceramic tiles, calcium sulphate screed, gypsum fibre boards

Dolfin Global Projects Private Limited, started in the year 2010 as a Limited Company, our firm is a well-known Service Provider And Manufacturer of Construction Services, Flooring Services, Waterproofing Services, Construction Chemicals, Waterproofing Chemical and many more. All these products are provided to the customer after tested on various quality strictures. All our business activities took place in our company’s headquarter located at Greater Noida, Uttar Pradesh. With the skilled administration of our knowledgeable workforce, we have been able to attain a huge client base in the market.

PRODUCT DATA SHEET SikaCeram®-125 Easy Fix Polymer modified cementitious tile adhesive for vitrified and ceramic tiles with no vertical slip DESCRIPTION SikaCeram®-125 Easy Fix is a polymer modified, cementitious, normal setting, self curing, easy fixing floor and wall tile adhesive. For small, medium sized ceramic and vitrified tiles in residential environments. Suitable for bonding absorbent and partly absorbent ceramic tiles to absorbent construction material substrates. Indoor use. EN 12004: Classification C1T*. USES Bonding the following types of tiles: ▪ Vitrified ▪ Ceramic ▪ Earthenware Bonding tiles for the following applications: ▪ Balconies ▪ Bathrooms ▪ Kitchens ▪ Residential environments ▪ Terraces ▪ Wet areas ▪ Tile on tile in any of above areas CHARACTERISTICS / ADVANTAGES ▪ Layer thickness: 1–10 mm ▪ Reduced vertical slip ▪ Smooth application ▪ Easy to use, only water to be added ▪ Better bond than conventional cement based mortar ▪ Self curing ▪ Bonding floor and wall tiles ▪ Suitable for absorbent ceramic tiles and vitrified tiles Typical bonding substrates: Cementitious screed, concrete, plaster, ceramic tiles

Sikament® FF T (VC) High performance admixture and compaction aid for wet semidry/no-slump concrete products Product Description Sikament® FF-T (VC) is a high performance compaction aid for semi-dry/no-slump concrete. Sikament® FF-T (VC) conforms to IS 9103-1999 Uses Sikament® FF-T (VC) is used for producing optimised coloured wet, semi-dry/noslump concrete with a very low water content. Wet,Semi-dry/no-slump concrete production is generally used in the manufacture of machine-made concrete products associated with instant de-moulding such as: Block Paving (grey / coloured) Cement Tiles (grey / coloured) Paving flags Kerbstones Edgings and other items for garden and landscape design Building blocks and bricks Characteristics / Advantages Sikament® FF-T (VC) offers substantial benefits to the producer of Wet, semi-dry/no slump concrete products: Efficient dispersion and distribution of cement, additives and pigments Give high early strength to wet concrete Improved movement of the concrete through the machine (faster mould filling) Optimised compaction with shorter pressing time and increased output [ shorter production cycle ] Minimized friction between the mould and the concrete [ Reductions in equipment wear and tear ] Reduced adhesion/stickiness between top layer concrete and pressing head/tamper (equipment/tools) Increased “green” strength on immediate de-moulding [ keeps the shape of freshly de-moulded semi-dry concrete products because it prevents slumping after de-moulding ] More economic concrete mix designs Create superior products Sikament® FF-T (VC) allows for the following advantages in the finished concrete products: Closer textured, smoother and more uniform surfaces (improved surface finish) Consistent product quality due to a homogenous concrete mix Less variation in densities and strengths across the area of the mould (constant spread of density & strength over the pallet) Minimized damage due to early handling Consistent early and ultimate compressive and tensile strengths Increased freeze-thaw resistance Improved durability and life expectancy Constant and uniform colour (colour fastness) Less customer returns and second grade products